Product Center
加速度傳感器中有一種是三軸加速度傳感器,同樣的它是基于加速度的基本原理去實現工作的,加速度是個空間矢量,一方面,要準確了解物體的運動狀態,必須測得其三個坐標軸上的分量;另一方面,在預先不知道物體運動方向的場合下,只有應用三軸加速度傳感器來檢測加速度信號。由于三軸加速度傳感器也是基于重力原理的,因此用三軸加速度傳感器可以實現雙軸正負90度或雙軸0-360度的傾角,通過校正后期精度要高于雙軸加速度傳感器大于測量角度為60度的情況。三軸加速度傳感器的好處就是在預先不知道物體運動方向的場合下,只有應用三維加速度傳感器來檢測加速度信號。三維加速度傳感器具有體積小和重量輕特點,可以測量空間加速度,能夠全面準確反映物體的運動性質。
美國Dytran的3033B2是一款微型三軸加速度傳感器/振動傳感器,壓電式工作原理,重量僅11g,集成石英剪切感應元件,不銹鋼外殼材質,適應于小質量的振動監測。
The Dytran 3033B2 is a low profile triaxial IEPE accelerometer with a height of 0.31 inches (7.9 millimeters) and a total weight of 11 grams. Featuring quartz shear sensing elements packaged in a rugged stainless steel housing for improved frequency response, the model 3033B2 is ideal for low mass vibration monitoring.
The model 3033B2 utilizes a 3-foot integral cable and thru hole mounting capabilities. This centralized screw mounting configuration allows for the sensor to be turned 360° prior to securing for ease of sensor installation. If desired, the accelerometer may also be adhesively mounted to the test article.
特性
1. 10 mV/g sensitivity
2. 500g range
3. 1 to 8,000 Hz frequency range (±5%)
4. 3-foot integral cable
5. Thru hole mount
6. 11 grams
7. Stainless steel
8. 360° cable orientation
9. Triaxial
10. IEPE
應用
1. Environmental Stress Screening (ESS)
環境應力篩選
2. Product response testing
產品響應測試
3. General purpose triaxial vibration measurements
一般目的三軸振動測量
WEIGHT (NOT INCLUDING CABLE) 11 GRAMS
SIZE, HxWxD 0.60 x 0.60 x 0.310 IN.
MOUNTING PROVISION, (THRU HOLE IN HSN’G) 4-40 X .420 LONG CAP SCREW
ELECTRICAL CONNECTIONS (3 BNC PLUGS) 3 FT.-8 INCHES LONG CABLE
MATERIAL, HOUSING & CABLE ADAPTOR 300 SERIES STAINLESS STEEL
MATERIAL, CABLE JACKET POLYURETHANE
PERFORMANCE
SENSITIVITY, +/- 20% (Measured at 100 Hz, 1 G, RMS) 10 mV/G
RANGE, F.S. for +/- 5 VOLTS OUT ±500 G's
FREQUENCY RESPONSE, +/- 5% 1 to 8000 Hz
MOUNTED RESONANT FREQUENCY, NOM. 40 kHz
ELECTRICAL NOISE FLOOR, EQUIVALENT .007 G
LINEARITY ±2 % F.S.
TRANSVERSE SENSITIVITY, MAX 5 %
ENVIRONMENTAL
MAXIMUM VIBRATION ±750 G
MAXIMUM SHOCK 1000 G, PEAK
TEMPERATURE RANGE -60 to +250 oF
COEFFICIENT OF THERMAL SENSITIVITY .03 %/oF
ENVIRONMENTAL SEAL EPOXY
ELECTRICAL
COMPLIANCE (SUPPLY) VOLTAGE RANGE +18 to +30 VDC
SUPPLY CURRENT RANGE (From constant current type power unit only) 2 to 20 mA
OUTPUT IMPEDANCE 100 OHMS
OUTPUT VOLTAGE BIAS, NOM. +10 VDC
DISCHARGE TIME CONSTANT, NOM. 0.5 SEC
OUTPUT SIGNAL POLARITY FOR ACCELERATION TOWARD CONVENTIONAL AXES POS
ELECTRICAL ISOLATION, signal/power ground to case >10 MEGW
訂貨型號
3033B2
相關型號
3313A1
3143D
產品分類
PRODUCT CLASSIFICATION